330104-00-06-10-02-CN Bently Nevada Proximity Sensor Metric

Bently Nevada 330104-00-06-10-02-CN 3300 XL 8 mm Proximity Probe – Technical Overview & Specifications

• Manufacturer: Bently Nevada (a brand of Baker Hughes). The 330104-00-06-10-02-CN ensures precision vibration and position monitoring.
• Probe Tip Material: Polyphenylene sulfide (PPS) withstands harsh industrial environments. The probe case uses AISI 303 or 304 stainless steel (SST).
• Linear Range: 2 mm (80 mils). The linear zone starts from 0.25 mm (10 mils) and extends to 2.3 mm (10 to 90 mils). Output spans approximately –1 to –17 Vdc.
• Recommended Radial Vibration Gap: Set the gap to –9 Vdc. This equals roughly 1.27 mm (50 mils) from the target.
• Probe DC Resistance (1.0m length): 7.59 ± 0.50 Ω (center conductor to outer conductor). The total length option for this model is 1.0 meter (3.3 feet).

Technical Specifications (Mechanical & Electrical)

• Model Number: 330104-00-06-10-02-CN. Unthreaded length: 00 mm. Overall case length: 60 mm. Connector type: Miniature coaxial ClickLoc with standard cable.
• Thread & Engagement: M10x1 probe case thread. Maximum thread engagement length equals 15 mm.
• Field Wiring Guidelines: Use 0.2 to 1.5 mm² (16 to 24 AWG). We recommend 3-conductor shielded triad cable with tinned wires. Maximum extension cable length between Proximitor Sensor and monitor: 305 meters (1,000 feet).
• Probe Weight: 323 g per meter (11.4 oz per meter). The compact design simplifies installation in tight spaces.

Environmental & Temperature Ratings

• Standard Probe Temperature Range (Operating/Storage): -52°C to +177°C (-62°F to +350°F). Do not expose the probe below –34˚C (-30˚F) to avoid pressure seal failure.
• Extended Temperature Range Probe: Tip handles -52°C to +218°C (-62°F to +425°F); cable and connector withstand -51°C to +260°C (-60°F to +500°F).
• Relative Humidity Performance: Less than 3% change in Average Scale Factor (ASF) after 56 days at 93% humidity (IEC 68 2 3).
• Pressure Sealing Design: The 3300 XL 8 mm probe seals differential pressure using a Viton® O-ring. The factory does not pressure test each unit before shipment.

Hazardous Area Approvals (Probe Only)

• Intrinsically Safe (ia): Suitable for Class I, Zone 0 AEx/Ex ia IIC T5...T1 Ga; also Class I, II, III for Groups A through G when used with zener barriers or galvanic isolators per drawing 141092.
• Non-incendive / nA, ec: Approved for Class I, Zone 2 AEx/Ex nA IIC T5…T1 Gc and Class I, Division 2 Groups A, B, C, D per drawing 140979.
• Temperature Schedule for EPL Ga/Gc: T1 (-55°C to +232°C), T2 (-55°C to +177°C), T3 (-55°C to +120°C), T4 (-55°C to +80°C), T5 (-55°C to +40°C).
• Temperature Schedule for EPL Dc: T280°C @ Ta (-55°C to +232°C), T225°C (-55°C to +177°C), T170°C (-55°C to +120°C), T130°C (-55°C to +80°C), T105°C (-55°C to +100°C), T90°C (-55°C to +40°C).

Installation & Wiring Guidance

• Mount the 330104-00-06-10-02-CN probe with the M10x1 thread. Ensure the thread engagement does not exceed 15 mm.
• Use the recommended -9 Vdc gap for radial vibration measurements. Always verify the target material and surface condition before final setup.
• For field wiring, keep total cable length within 305 meters (1,000 feet) to prevent high-frequency signal rolloff. Refer to frequency response graphs for specific attenuation.
• Do not expose the probe to temperatures below –34˚C (-30˚F) during operation. This action may damage the Viton® pressure seal prematurely.

Frequently Asked Questions (FAQ)

• Q: Is the 330104-00-06-10-02-CN a genuine new probe?
  A: Yes, we supply only brand new original Bently Nevada probes. We never sell counterfeit or used units.
• Q: What is the linear range of the 3300 XL 8 mm probe?
  A: The linear range equals 2 mm (80 mils), starting from 0.25 mm to 2.3 mm (10 to 90 mils) from the target.
• Q: Can I use this probe with a 5-meter extension cable?
  A: Yes, but the total distance between Proximitor Sensor and monitor must not exceed 305 meters (1,000 feet). Longer cables reduce high-frequency response.
• Q: How do I set the recommended gap for radial vibration?
  A: Adjust the probe position until the output reads –9 Vdc. This usually corresponds to 1.27 mm (50 mils) gap.
• Q: What happens if I operate the probe below -34°C (-30°F)?
  A: The pressure seal may fail prematurely. Keep the probe within the specified temperature range for reliable sealing.
• Q: Do you test the pressure seal before shipping?
  A: Bently Nevada does not pressure test each probe. Contact their custom design department if your application requires a seal test.
• Q: What is the nominal DC resistance for the 1.0m version?
  A: The resistance from center to outer conductor measures 7.59 ± 0.50 Ω.
• Q: How long until you ship the order?
  A: We dispatch all orders within 5 business days. You will receive tracking via FedEx, UPS, or DHL.
• Q: Can I return the probe if I change my mind?
  A: Yes, we accept returns within 30 days. The item must stay unused and in original condition.
• Q: Does the package include any certificate or 12-month warranty?
  A: No, the box contains the probe and basic documentation only. Warranty terms appear separately on our policy page.

© 2026 NexAuto Technology Limited. All rights reserved.
Original Source: https://www.nex-auto.com/
Contact: sales@nex-auto.com | Phone: +86 153 9242 9628 (click to chat via WhatsApp)