ABB MPS IV SPS01 Power Supply 24V 10A

ABB MPS IV SPS01 Power Supply - 24V 10A - 2VAA008278R001

ABB powers your control system reliably. The MPS IV SPS01 (Part 2VAA008278R001) delivers 24V DC at 10 amps. This DIN rail power supply feeds PLCs, relays, and sensors. Use it in industrial cabinets worldwide.

Core Specs

• Brand: ABB
• Model: MPS IV SPS01
• Part Number: 2VAA008278R001
• Type: Industrial Power Supply
• Output Voltage: 24 V DC
• Output Current: 10 A continuous
• Output Power: 240 W

Input Ratings

• Input Voltage: 85 to 264 V AC (universal)
• Input Frequency: 47 to 63 Hz
• Input Current: 2.5 A at 115V, 1.3 A at 230V
• Inrush Current: 30 A max (cold start)
• Power Factor: 0.92 typical

Output Details

• Adjustment Range: 22 to 28 V DC
• Ripple & Noise: < 50 mV peak-peak
• Line Regulation: ±0.5%
• Load Regulation: ±1.0%
• Hold-up Time: 20 ms at full load
• Start-up Time: 1.5 seconds

Efficiency & Power

• Efficiency: 90% at 230V AC
• Power Loss: 27 W max
• No-load Power: < 0.5 W (green mode)

Protection Features

• Overload: 105-150% of rated, hiccup mode
• Over Voltage: 28-33 V, latch off
• Short Circuit: Continuous, auto recovery
• Over Temperature: Shutdown at 85°C, auto restart

Environment

• Operating Temp: -25°C to +70°C
• Derating: 2.5% per °C above 50°C
• Storage Temp: -40°C to +85°C
• Humidity: 5% to 95% non-condensing
• Cooling: Natural convection

Physical

• Size (H x W x D): 124 x 70 x 115 mm
• Weight: 0.8 kg
• Mounting: DIN rail (35mm EN 60715)
• Housing: Metal, IP20

Terminals

• Input: Screw terminals (L, N, PE)
• Output: Screw terminals (+V, -V)
• Wire Size: 0.5 to 4 mm² (AWG 20-12)
• Torque: 0.8 Nm

LED & Indicators

• DC OK (Green): Output voltage present
• Overload (Red): Current limit active

Compliance

• CE Mark: Yes
• UL Listed: UL 508
• RoHS: Yes
• HS Code: 85044095

Box Contains

• MPS IV SPS01 power supply unit
• DIN rail mounting clip (pre-installed)
• Quick start guide

Shipping

• Weight: ~0.9 kg packed
• Carriers: FedEx, UPS, DHL

FAQ

• Can I parallel two SPS01 units?
  Yes. Use diodes on each output. Derate each to 8A max.
• What does MPS IV stand for?
  Modular Power Supply 4th generation. It's ABB's industrial series.
• Does this run on 120V AC?
  Yes. Universal input 85-264V works worldwide.
• Is there a remote on/off?
  No. Connect input via external breaker or switch.
• What happens on overload?
  Hiccup mode: unit restarts every 5 seconds until fault clears.

Install Tips

• Ventilation: Leave 30 mm gap above and below for air flow.
• Parallel caution: Use blocking diodes. Mismatched voltages cause circulating current.
• High ambient: Above 50°C, reduce load by 2.5% per °C.
• Input fuse: Use 4A slow-blow external fuse per local code.