A02B-0120-C041 FANUC CRT/MDI Operator Interface

A02B-0120-C041 FANUC 9-Inch Monochrome CRT/MDI Unit for Series 16/18 CNC

Technical Specifications

• Brand: FANUC
• Model: A02B-0120-C041
• Category: CRT/MDI operator interface unit (display and input panel)
• Series: FANUC Series 16/18 CNC
• Display: 9-inch monochrome CRT
• Input: MDI keyboard unit integrated in the same panel
• Supply voltage: No published manufacturer value for this order code; early CRT/MDI design
• Power consumption: No published manufacturer value for this order code
• Operating temperature: 0 to 55 °C (family-level reference, not confirmed for this order code)
• Storage/transport temperature: −20 to 60 °C (family-level reference, not confirmed for this order code)
• Relative humidity: 75%RH or less, no condensation
• Dimensions (H×W×D): 203 × 400 × 241 mm (supplier-reported, single source)
• Weight: approximately 4.51 kg (supplier-reported, single source)

Key Technical Points

• The CRT display shows monochrome text and graphics for operator feedback.
• The MDI keyboard handles manual data input and machine operation commands.
• The unit works as a passive component and carries no built-in communication ports.
• The 0 to 55 °C operating window suits typical machine-tool cabinet conditions.
• The 75%RH humidity limit with no condensation supports stable electrical operation.
• Family references for temperature come from GFZ-63003EN/04 for the 16i-A control.
• No official document confirms these values for this specific order code.
• No published measurement range, frequency response, sensitivity or linearity data exists.
• The CRT design gives way to LCD panels in current FANUC CNC generations.

Installation Guide

• Confirm the control is a FANUC Series 16/18 CNC and check the suffix code.
• Compare the 203 × 400 × 241 mm panel outline with the cabinet cutout first.
• Power down the CNC and lock out the supply before you start the swap.
• Keep the ambient temperature inside the 0 to 55 °C window during operation.
• Hold relative humidity at 75%RH or less and avoid condensation on the panel.
• Seat the MDI keyboard connector fully and check each cable route.
• Run a display and key test cycle after you restore power.
• Verify the final wiring against official FANUC documentation.

Packing List

• 1 × A02B-0120-C041 CRT/MDI operator interface unit
• 1 × protective foam set and antistatic bag
• 1 × outer shipping carton

Shipping

• We ship orders within 5 days after payment clears.
• We use FedEx, UPS and DHL for international delivery.
• We pack each unit with shock-absorbing material for CRT protection.

FAQ

• Q: Does the A02B-0120-C041 fit every FANUC Series 16/18 control?
  A: No. The suffix variants select the control type, so confirm your order code first.
• Q: What supply voltage does this CRT/MDI unit need?
  A: FANUC publishes no voltage value for this order code, so check the machine wiring diagram.
• Q: What is the operating temperature range?
  A: Family references give 0 to 55 °C, but no document confirms this for the order code.
• Q: How much does the unit weigh?
  A: Supplier data lists about 4.51 kg, and the panel measures 203 × 400 × 241 mm.
• Q: Does the unit have communication ports?
  A: No. It works as a passive component and carries no built-in communication ports.
• Q: What is the condition and stock status?
  A: The unit is brand new and original, and we hold stock for immediate orders.
• Q: What is the return policy?
  A: We support returns within 30 days of delivery.