Bently Nevada 330192-00-08-05-CN Probe

Bently Nevada 330192-00-08-05-CN Country Specific ETR Probe

• Manufacturer & Model: Bently Nevada 330192-00-08-05-CN ETR probe for 3300 XL series.
• Product Type: 8 mm Eddy Current Transducer with stainless steel armor.
• Thread: 3/8-24 UNF.
• Agency Approval: CN = Country Specific (varies by destination).
• Made in: U.S.A.

Country Specific Approval (CN)

• CN designation: Approval requirements vary by destination country.
• Typical certifications: May include local safety marks or regional standards.
• Common regions: Brazil (INMETRO), China (NEPSI), India (PESO), or other local bodies.
• Verification needed: Confirm specific approvals for your country before ordering.
• Documentation: Country specific certificates available upon request.

Ultra Short Design

• Case length: Only 0.8 inches (20.3 millimeters).
• Cable length: 0.5 meter (1.6 feet).
• Unthreaded section: Zero - threads start at shoulder.
• Maximum wall thickness: 0.2 inches (5 millimeters).
• Best for: Tight spaces, thin casings, retrofits.

Electrical Specifications

• RPROBE at 0.5 meter: 7.45 ± 0.50 Ohms.
• Supply voltage: -17.5 to -26 Vdc, nominal -24 Vdc.
• Output voltage swing: -2 to -18 Vdc over linear range.
• Sensitivity: 7.87 V/mm (200 mV/mil).
• Linear range: 2 millimeters (80 mils).
• Frequency response: 0 to 10 kHz.

Temperature Ratings

• Standard operating: -52 to 177 degrees Celsius.
• Extended tip: Up to 218 degrees Celsius.
• Extended cable: -51 to 260 degrees Celsius.
• Pressure seal warning: Below -34 degrees Celsius may cause seal failure.
• Storage temperature: Same as operating range.

Physical Specifications

• Probe diameter: 8 millimeters tip.
• Case material: AISI 303 or 304 stainless steel.
• Tip material: Polyphenylene sulfide (PPS).
• Maximum thread engagement: 0.563 inches.
• Armor type: Stainless steel over cable.
• Connector: Standard 3300 XL coaxial.

Humidity Performance

• Test standard: IEC 68-2-3 for up to 56 days.
• Test humidity: 93 percent relative humidity.
• Performance change: Less than 3 percent change in Average Scale Factor.
• Result: Suitable for high humidity environments.

Pressure Seal Information

• Seal material: Viton O-ring between tip and case.
• Function: Seals differential pressure at mounting point.
• Factory test: Not performed before shipment.
• Custom option: Contact design department for pressure testing.

System Compatibility

• Proximitor: 3300 XL 8mm (330180-90-00).
• Extension cables: 3300 XL series only.
• Target material: Calibrated for AISI 4140 steel.
• Monitoring systems: 3500 Series, 1900 Series, 2300 Series.

Package Contents

• Probe assembly: 330192-00-08-05-CN with 0.5m armored cable.
• Lock nut: 3/8-24 UNF hex nut.
• Calibration certificate: Individual sensitivity data.
• Documentation: Installation instructions.
• Connector cap: Plastic protector for storage.

Shipping Information

• Shipping weight: 0.3 kilograms (0.66 pounds).
• Packaging: Small cardboard tube.
• Carriers: FedEx, UPS, DHL (2 to 5 business days).

Frequently Asked Questions

• Q: What does Country Specific (CN) approval mean for this probe?
  A: CN approval varies by destination country. Unlike standard approvals (00 = none, 05 = CSA/ATEX/IECEx), CN is customized for local regulations. Contact Bently Nevada for specific country certifications before ordering.
• Q: What is the maximum wall thickness for this 0.8 inch probe?
  A: Safe maximum is 0.2 inches (5 millimeters). Calculation: 0.8 inch case minus 0.5 inch minimum thread engagement minus 0.06 inch gap equals 0.24 inches maximum with no safety margin.
• Q: Can I use this probe in temperatures below -34 degrees Celsius?
  A: The probe operates to -52 degrees Celsius, but the Viton pressure seal may fail below -34 degrees Celsius. For sustained cold operation, request extended temperature range probe with special sealing materials.
• Q: Is the CN approval the same as option 05 (CSA/ATEX/IECEx)?
  A: No. Option 05 provides specific global certifications. CN approval is customized per country. CN may include different certification bodies or local requirements not covered by standard options.
• Q: Does the 0.5 meter cable limit my installation?
  A: Add 3300 XL extension cables to reach longer distances. Total system length (probe cable plus extension) must match your proximitor calibration. Example: 0.5 meter probe plus 4.5 meter extension equals 5.0 meter system.